The NUX TIME CORE DELUXE MKII is a delay pedal with 7 different types and a phrase looper; including ΦPhi Digital Delay, Analog Delay, Modulation Delay, Tape Echo, Pan Delay, Verb Delay, Reverse Delay and Sound On Sound. You can switch the delay type by using the Type rotary switch.
Features
- 7 delay types in a compact enclosure.
- ΦPhi Digital Delay: Musical digital delay with golden ratio 2nd repeat head. (80ms~1000ms)
- Analog Delay: Warm sound with natural treble decay. (40ms~403ms)
- Modulation Delay: Lush and rich chorus with digital delay. (20ms~1500ms)
- Tape Echo: High-frequency saturation and low-end decay. (55ms~552ms)
- Pan Delay: Creative natural stereo feeling. (80ms~1000ms)
- Verb Delay: Plate Reverb algorithm with Digital Delay to create an ambient atmosphere. (80ms~1000ms)
- Reverse Delay: Inspire guitarists for new ideas. (320ms~1240ms)
- S.O.S: 40 seconds stereo phrase loop.
- Sub-division with Smart Tap Tempo. (Maximum: 1580ms)
- True-bypass or Buffer-bypass(Tails).
- Supports Stereo.
- Kill Dry.
- Low power consumption. (less than 120mA)
- Analog dry signal for low noise and zero latency.
Specifications
- Input Impedance: 1MΩ
- Output Impedance: 1kΩ
- Dynamic Range: 104 dB
- DSP Processing: 48KHz / 32-bit
- A/D D/A Sampling Rate: 48KHz / 24-bit
- Power: 9V DC(Negative tip, Optional ACD-006A adapter)
- Current Draw: less than 120mA
- Dimensions: 122(L) X 72(W) X 47(H)mm
- Weight: 270g
In S.O.S mode, the footswitch operation is like a regular looper pedal. While REC, the LED indicator shows RED, while PLAY, the LED indicator shows GREEN, while OVERDUB, the LED indicator shows ORANGE.
In Mod.D & Verb style, holding the footswitch will enter Alt mode (the LED indicator will flash ORANGE), you can then adjust the Mod or Verb parameters via the Repeat knob. Short press the footswitch to quit Alt mode.
Kill Dry: Without any USB connection, hold the footswitch to boot-up the pedal, if the LED indicator flash GREEN 3 times, the KILL DRY is engaged. If the LED indicator flashes RED 3 times, the KILL DRY is disengaged. (Normal)
I/O Jacks
- DC jack
Use ONLY: 9V Negative Tip power with more than 150mA. (The power consumption is less than 125mA.)
- USB-C port
The USB-C port is for firmware updates. Connect USB cable to a PC and hold the footswitch to boot-up the device and to enter the DFU (Device Firmware Update) mode. Once connected you can perform firmware updates using DFU updater software.
Download the related firmware and firmware update guide from product page.
- In jacks
The audio inputs on the right side of this pedal are standard 1/4" jacks (mono/TS). Connect your guitar to the In (mono) audio input on the right side of your pedal using a regular 1/4" instrument cable.1
The pedal also accepts stereo signals using a pair of 1/4" TS cables.
- Out jacks
The audio outputs on the left side of this pedal are standard 1/4" jacks (mono/TS). Connect the audio output of your pedal to the next device in the signal chain, either with a single cable or with a pair of 1/4" cables if both inputs are used.
Connections
If the amp’s FX loop is parallel, you will need to engage Kill Dry.
Kill Dry: Without USB connection, hold the footswitch to boot-up the pedal, if the LED indicator flash GREEN 3 times, the KILL DRY is engaged. If the LED indicator flashes RED 3 times, the KILL DRY is disengaged. (Normal)